If you are planning to study Forestry and Wood Technology at Federal University of Technology Minna located in Niger State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. FUTMINNA was established in 1983 by the Federal Government of Nigeria as a specialized university of technology. The institution was created to support technological innovation and produce skilled manpower for national development. This page explains everything you need to know to increase your chances of gaining admission into FUTMINNA.
Does Federal University of Technology Minna (FUTMINNA) offer Forestry and Wood Technology?
No, Federal University of Technology Minna does not offer Forestry and Wood Technology under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology Minna (FUTMINNA) below to check if the Forestry and Wood Technology course under the Faculty of Agriculture has been updated.
Admission Requirements for Forestry and Wood Technology When Accredited in Federal University of Technology Minna (FUTMINNA)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Forestry and Wood Technology department under Faculty of Agriculture, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science,
at least ‘O’ Level pass in Physics.
JAMB Subject Combination
Mathematics / Physics and
Biology / Agricultural Science.
FUTMINNA Cut-Off Mark for Forestry and Wood Technology
The general UTME cut-off mark is 180, but due to the variation of Forestry and Wood Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTMINNA Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTMINNA Science Courses with their Requirements
1. Information and Media Technology
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Information and Media Technology department.
two (2) other Science subjects.
2. Metallurgical and Material Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Metallurgical and Material Engineering department.
one other Science subject.
3. Geography
To study this course, the minimum requirement for applicants seeking admission to the Geography department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other two (2) Science subjects.
4. Microbiology
To study this course, candidates aspiring to gain admission into Microbiology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
5. Architecture
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
6. Agricultural and Bioresources Engineering
To study this course, the minimum requirement for applicants seeking admission to the Agricultural and Bioresources Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Introduction to Agricultural Science, Materials and Workshop Process and Machining, Tractor Layout Power Unit Under Carriage and Auto Electricity; Transmission System; Implement and Machine;
Principles of Crop Husbandry and Land Use, Materials and Workshop Processes; Construction and Maintenance of Agricultural Machines; General Metal Work; General Wood Work and Building / Engineering Drawing.
7. Animal Production
To study this course, candidates aspiring to gain admission into Animal Production department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science.
Nigerian Tertiary Institutions Offering Forestry and Wood Technology Course