If you are planning to study Plant Breeding and Seed Science at Federal University of Technology Minna located in Niger State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. FUTMINNA was established in 1983 by the Federal Government of Nigeria as a specialized university of technology. The institution was created to support technological innovation and produce skilled manpower for national development. This page explains everything you need to know to increase your chances of gaining admission into FUTMINNA.
Does Federal University of Technology Minna (FUTMINNA) offer Plant Breeding and Seed Science?
No, Federal University of Technology Minna does not offer Plant Breeding and Seed Science under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology Minna (FUTMINNA) below to check if the Plant Breeding and Seed Science course under the Faculty of Agriculture has been updated.
Admission Requirements for Plant Breeding and Seed Science When Accredited in Federal University of Technology Minna (FUTMINNA)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Plant Breeding and Seed Science department under Faculty of Agriculture, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science,
at least O’Level pass in Physics.
JAMB Subject Combination
Mathematics / Physics and
Biology / Agricultural Science.
FUTMINNA Cut-Off Mark for Plant Breeding and Seed Science
The general UTME cut-off mark is 180, but due to the variation of Plant Breeding and Seed Science cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTMINNA Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTMINNA Science Courses with their Requirements
1. Telecommunication Engineering
To study this course, the minimum requirement for applicants seeking admission to the Telecommunication Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subjects.
2. Electrical and Computer Engineering
To study this course, candidates seeking admission into the Electrical and Computer Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any one other relevant subject.
3. Horticulture
To study this course, candidates aspiring to gain admission into Horticulture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology or Agric Science, and
any one other relevant subject.
4. Computer Engineering
To study this course, candidates aspiring to gain admission into Computer Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
5. Building
To study this course, the minimum requirement for applicants seeking admission to the Building department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
6. Agricultural and Bioresources Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Agricultural and Bioresources Engineering department.
Introduction to Agricultural Science, Materials and Workshop Process and Machining, Tractor Layout Power Unit Under Carriage and Auto Electricity; Transmission System; Implement and Machine;
Principles of Crop Husbandry and Land Use, Materials and Workshop Processes; Construction and Maintenance of Agricultural Machines; General Metal Work; General Wood Work and Building / Engineering Drawing.
7. Urban and Regional Planning (URP)
To study this course, candidates seeking admission into the Urban and Regional Planning (URP) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Nigerian Tertiary Institutions Offering Plant Breeding and Seed Science Course