If you are planning to study Environmental Management and Toxicology at Federal University of Technology, Owerri located in Imo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUTO.
Does Federal University of Technology, Owerri (FUTO) offer Environmental Management and Toxicology?
No, Federal University of Technology, Owerri does not offer Environmental Management and Toxicology under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology, Owerri (FUTO) below to check if the Environmental Management and Toxicology course under the Faculty of Science has been updated.
Admission Requirements for Environmental Management and Toxicology When Accredited in Federal University of Technology, Owerri (FUTO)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Environmental Management and Toxicology department under Faculty of Science.
JAMB Subject Combination
either Physics or Mathematics.
FUTO Cut-Off Mark for Environmental Management and Toxicology
The general UTME cut-off mark is 180, but due to the variation of Environmental Management and Toxicology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTO Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTO Science Courses with their Requirements
1. Radiography
To study this course, candidates seeking admission into the Radiography department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
2. Metallurgical and Material Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Metallurgical and Material Engineering department.
one other Science subject.
3. Animal Science and Technology
To study this course, the minimum requirement for applicants seeking admission to the Animal Science and Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agric Science and
4. Architecture
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
5. Medicine and Surgery
To study this course, the minimum requirement for applicants seeking admission to the Medicine and Surgery department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
6. Urban and Regional Planning (URP)
To study this course, candidates seeking admission into the Urban and Regional Planning (URP) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
7. Building
To study this course, candidates seeking admission into the Building department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Nigerian Universities Offering Environmental Management and Toxicology Course