If you are planning to study Geology and Mineral Sciences at Federal University of Technology, Owerri located in Imo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. FUTO was established in 1980 by the Federal Government of Nigeria as a university of technology aimed at promoting scientific advancement and technological education. It has grown into one of Nigeria’s leading technology-focused universities. This page explains everything you need to know to increase your chances of gaining admission into FUTO.
Does Federal University of Technology, Owerri (FUTO) offer Geology and Mineral Sciences?
No, Federal University of Technology, Owerri does not offer Geology and Mineral Sciences under its Faculty of Earth and Mineral Sciences. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology, Owerri (FUTO) below to check if the Geology and Mineral Sciences course under the Faculty of Earth and Mineral Sciences has been updated.
Admission Requirements for Geology and Mineral Sciences When Accredited in Federal University of Technology, Owerri (FUTO)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Geology and Mineral Sciences department under Faculty of Earth and Mineral Sciences, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
JAMB Subject Combination
Use of English and any three (3) of
FUTO Cut-Off Mark for Geology and Mineral Sciences
The general UTME cut-off mark is 180, but due to the variation of Geology and Mineral Sciences cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTO Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTO Science Courses with their Requirements
1. Civil Engineering
To study this course, candidates aspiring to gain admission into Civil Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
2. Fisheries and Aquaculture Technology
To study this course, the minimum requirement for applicants seeking admission to the Fisheries and Aquaculture Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science,
Physics / Geography / Economics.
3. Software Engineering
To study this course, candidates seeking admission into the Software Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subjects.
4. Building
To study this course, candidates aspiring to gain admission into Building department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
5. Polymer and Textile Engineering
To study this course, candidates aspiring to gain admission into Polymer and Textile Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
6. Forensic Science
To study this course, candidates aspiring to gain admission into Forensic Science department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
7. Surveying and Geoinformatics
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Nigerian Tertiary Institutions Offering Geology and Mineral Sciences Course