If you are planning to study Industrial Engineering at Federal University of Technology, Owerri located in Imo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. FUTO was established in 1980 by the Federal Government of Nigeria as a university of technology aimed at promoting scientific advancement and technological education. It has grown into one of Nigeria’s leading technology-focused universities. This page explains everything you need to know to increase your chances of gaining admission into FUTO.
Does Federal University of Technology, Owerri (FUTO) offer Industrial Engineering?
No, Federal University of Technology, Owerri does not offer Industrial Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology, Owerri (FUTO) below to check if the Industrial Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Industrial Engineering When Accredited in Federal University of Technology, Owerri (FUTO)
O’Level Requirements
To study this course, candidates seeking admission into the Industrial Engineering department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
FUTO Cut-Off Mark for Industrial Engineering
The general UTME cut-off mark is 180, but due to the variation of Industrial Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTO Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTO Science Courses with their Requirements
1. Quantity Surveying (QS)
To study this course, the minimum requirement for applicants seeking admission to the Quantity Surveying (QS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
2. Architecture
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
3. Food Science and Technology (FT)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Food Science and Technology (FT) department.
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
4. Metallurgical and Material Engineering
To study this course, candidates seeking admission into the Metallurgical and Material Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
one other Science subject.
5. Biotechnology
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Biotechnology department.
6. Statistics
To study this course, candidates aspiring to gain admission into Statistics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other relevant subject.
7. Software Engineering
To study this course, candidates aspiring to gain admission into Software Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
two (2) other Science subjects.
Nigerian Tertiary Institutions Offering Industrial Engineering Course