If you are planning to study Pure Physics at Federal University of Technology, Owerri located in Imo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. FUTO was established in 1980 by the Federal Government of Nigeria as a university of technology aimed at promoting scientific advancement and technological education. It has grown into one of Nigeria’s leading technology-focused universities. This page explains everything you need to know to increase your chances of gaining admission into FUTO.
Does Federal University of Technology, Owerri (FUTO) offer Pure Physics?
No, Federal University of Technology, Owerri does not offer Pure Physics under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology, Owerri (FUTO) below to check if the Pure Physics course under the Faculty of Science has been updated.
Admission Requirements for Pure Physics When Accredited in Federal University of Technology, Owerri (FUTO)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Pure Physics department under Faculty of Science, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject from:
Biology or Agricultural Science.
FUTO Cut-Off Mark for Pure Physics
The general UTME cut-off mark is 180, but due to the variation of Pure Physics cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTO Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTO Science Courses with their Requirements
1. Biology
To study this course, candidates aspiring to gain admission into Biology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Mathematics / Physics and
any one other relevant subject.
2. Science Laboratory Technology (SLT)
To study this course, the minimum requirement for applicants seeking admission to the Science Laboratory Technology (SLT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
3. Statistics
To study this course, the minimum requirement for applicants seeking admission to the Statistics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other relevant subject.
4. Quantity Surveying (QS)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Quantity Surveying (QS) department.
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
5. Petroleum Engineering
To study this course, candidates aspiring to gain admission into Petroleum Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
6. Fisheries and Aquaculture Technology
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Fisheries and Aquaculture Technology department.
Biology / Agricultural Science,
Physics / Geography / Economics.
7. Surveying and Geoinformatics
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Nigerian Tertiary Institutions Offering Pure Physics Course