If you are planning to study Industrial Technical Education at Federal University, Oye-Ekiti located in Ekiti State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. FUOYE was established in 2011 by the Federal Government of Nigeria as part of a nationwide initiative to expand university education. The institution has grown rapidly and is recognized for its commitment to quality teaching and research. This page explains everything you need to know to increase your chances of gaining admission into FUOYE.
Does Federal University, Oye-Ekiti (FUOYE) offer Industrial Technical Education?
No, Federal University, Oye-Ekiti does not offer Industrial Technical Education under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Federal University, Oye-Ekiti (FUOYE) below to check if the Industrial Technical Education course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Industrial Technical Education When Accredited in Federal University, Oye-Ekiti (FUOYE)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Industrial Technical Education department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Mathematics / Physics and
any other three (3) relevant subjects.
FUOYE Cut-Off Mark for Industrial Technical Education
The general UTME cut-off mark is 180, but due to the variation of Industrial Technical Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUOYE Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUOYE Science Courses with their Requirements
1. Crop Science and Horticulture
To study this course, candidates aspiring to gain admission into Crop Science and Horticulture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science,
one Science/Social Science subject and
at least ‘O’ Level pass in Physics.
2. Building
To study this course, candidates seeking admission into the Building department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
3. Food Science and Technology (FT)
To study this course, the minimum requirement for applicants seeking admission to the Food Science and Technology (FT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
4. Metallurgical and Material Engineering
To study this course, candidates seeking admission into the Metallurgical and Material Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
one other Science subject.
5. Teacher Education Science
To study this course, the minimum requirement for applicants seeking admission to the Teacher Education Science department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subjects.
6. Mechanical Engineering
To study this course, candidates seeking admission into the Mechanical Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant Science subjects.
7. Mechatronics Engineering
To study this course, the minimum requirement for applicants seeking admission to the Mechatronics Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
Nigerian Tertiary Institutions Offering Industrial Technical Education Course