If you are planning to study Mechanical Metalwork Technology Education at Federal University, Oye-Ekiti located in Ekiti State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUOYE.
Does Federal University, Oye-Ekiti (FUOYE) offer Mechanical Metalwork Technology Education?
No, Federal University, Oye-Ekiti does not offer Mechanical Metalwork Technology Education under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Federal University, Oye-Ekiti (FUOYE) below to check if the Mechanical Metalwork Technology Education course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechanical Metalwork Technology Education When Accredited in Federal University, Oye-Ekiti (FUOYE)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Mechanical Metalwork Technology Education department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
one (1) of Biology /Agricultural Science; Physics, or Chemistry and
two (2) from General Science/IntegratedScience, Technical Drawing/Fine Art, Health Science Food and Nutrition,
Geography, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
JAMB Subject Combination
any other relevant subject.
FUOYE Cut-Off Mark for Mechanical Metalwork Technology Education
The general UTME cut-off mark is 180, but due to the variation of Mechanical Metalwork Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUOYE Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUOYE Science Courses with their Requirements
Geology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Geology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other relevant subject.
Surveying and Geoinformatics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Anatomy
SSCE Requirements
To study this course, candidates aspiring to gain admission into Anatomy department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Computer Science (CS)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer Science (CS) department.
any two (2) other Science subjects.
Education and Chemistry
SSCE Requirements
To study this course, candidates seeking admission into the Education and Chemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology and Agricultural Science.
Metallurgical and Material Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Metallurgical and Material Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
one other Science subject.
Health Education
SSCE Requirements
To study this course, candidates aspiring to gain admission into Health Education department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subjects.
Nigerian Tertiary Institutions Offering Mechanical Metalwork Technology Education Course