If you are planning to study Polymer Engineering at Federal University, Oye-Ekiti located in Ekiti State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. FUOYE was established in 2011 by the Federal Government of Nigeria as part of a nationwide initiative to expand university education. The institution has grown rapidly and is recognized for its commitment to quality teaching and research. This page explains everything you need to know to increase your chances of gaining admission into FUOYE.
Does Federal University, Oye-Ekiti (FUOYE) offer Polymer Engineering?
No, Federal University, Oye-Ekiti does not offer Polymer Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Federal University, Oye-Ekiti (FUOYE) below to check if the Polymer Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Polymer Engineering When Accredited in Federal University, Oye-Ekiti (FUOYE)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Polymer Engineering department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
FUOYE Cut-Off Mark for Polymer Engineering
The general UTME cut-off mark is 180, but due to the variation of Polymer Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUOYE Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUOYE Science Courses with their Requirements
1. Crop Science and Horticulture
To study this course, candidates aspiring to gain admission into Crop Science and Horticulture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science,
one Science/Social Science subject and
at least ‘O’ Level pass in Physics.
2. Industrial Chemistry
To study this course, candidates aspiring to gain admission into Industrial Chemistry department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science.
3. Urban and Regional Planning (URP)
To study this course, the minimum requirement for applicants seeking admission to the Urban and Regional Planning (URP) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
4. Education and Chemistry
To study this course, candidates aspiring to gain admission into Education and Chemistry department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology and Agricultural Science.
5. Environmental Management and Toxicology
To study this course, candidates seeking admission into the Environmental Management and Toxicology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
6. Food Science and Technology (FT)
To study this course, candidates seeking admission into the Food Science and Technology (FT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
7. Quantity Surveying (QS)
To study this course, candidates seeking admission into the Quantity Surveying (QS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
Nigerian Tertiary Institutions Offering Polymer Engineering Course