If you are planning to study Forestry and Wildlife at Gateway Polytechnic, Saapade located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Gateway Polytechnic Saapade.
Does Gateway Polytechnic, Saapade offer Forestry and Wildlife?
No, Gateway Polytechnic, Saapade does not offer Forestry and Wildlife under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Gateway Polytechnic, Saapade below to check if the Forestry and Wildlife course under the Faculty of Agriculture has been updated.
Admission Requirements for Forestry and Wildlife When Accredited in Gateway Polytechnic, Saapade
O’Level Requirements
To study this course, candidates seeking admission into the Forestry and Wildlife department under Faculty of Agriculture, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Further Mathematics and Statistics.
JAMB Subject Combination
Biology / Agriculture and
Gateway Polytechnic Saapade Cut-Off Mark for Forestry and Wildlife
The general UTME cut-off mark is 180, but due to the variation of Forestry and Wildlife cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Gateway Polytechnic Saapade Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Gateway Polytechnic Saapade Science Courses with their Requirements
Food Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Food Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science,
any two of the following:
Geography, Food and Nutrition, Economics, Technical Drawing, Physics, Chemistry, Nigerian Language and Home Economics.
At least a pass in Chemistry is required.
Building Technology (BT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Architectural Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architectural Technology department.
Biology, Fine Art, Chemistry, History, English Language, Geography, Further Mathematics, Economics / Commerce, Religious Knowledge, Technical Drawing and Business Method.
At least a pass in Fine Art or Technical Drawing.
Estate Management and Valuation
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Estate Management and Valuation department.
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Computer Science (CS)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Computer Science (CS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other Science subjects.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Science Laboratory Technology (SLT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Welding and Fabrication Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Welding and Fabrication Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
Nigerian Tertiary Institutions Offering Forestry and Wildlife Course