If you are planning to study Mechanical Metalwork Technology Education at Godfrey Okoye University located in Enugu State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. GOUNI was established in 2009 by the Catholic Diocese of Enugu to provide holistic university education grounded in academic excellence, ethical values, and community development. It has since expanded into one of Nigeria’s leading private universities. This page explains everything you need to know to increase your chances of gaining admission into GOUNI.
Does Godfrey Okoye University (GOUNI) offer Mechanical Metalwork Technology Education?
No, Godfrey Okoye University does not offer Mechanical Metalwork Technology Education under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Godfrey Okoye University (GOUNI) below to check if the Mechanical Metalwork Technology Education course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechanical Metalwork Technology Education When Accredited in Godfrey Okoye University (GOUNI)
O’Level Requirements
To study this course, candidates seeking admission into the Mechanical Metalwork Technology Education department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
one (1) of Biology /Agricultural Science; Physics, or Chemistry and
two (2) from General Science/IntegratedScience, Technical Drawing/Fine Art, Health Science Food and Nutrition,
Geography, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
JAMB Subject Combination
any other relevant subject.
GOUNI Cut-Off Mark for Mechanical Metalwork Technology Education
The general UTME cut-off mark is 180, but due to the variation of Mechanical Metalwork Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from GOUNI Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other GOUNI Science Courses with their Requirements
1. Physics With Electronics
To study this course, candidates seeking admission into the Physics With Electronics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject from Further Mathematics and Biology / Agricultural Science.
2. Physical Science
To study this course, the minimum requirement for applicants seeking admission to the Physical Science department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject from:
Biology or Agricultural Science.
3. Education and Physics
To study this course, candidates aspiring to gain admission into Education and Physics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
two (2) other Science subjects or NTC / NBC.
4. Industrial Physics
To study this course, the minimum requirement for applicants seeking admission to the Industrial Physics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject from Further Mathematics and Biology or Agricultural Science.
5. Biotechnology
To study this course, candidates seeking admission into the Biotechnology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
6. Architecture
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
7. Education and Biology
To study this course, the minimum requirement for applicants seeking admission to the Education and Biology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Nigerian Tertiary Institutions Offering Mechanical Metalwork Technology Education Course