If you are planning to study Chemical and Polymer Engineering at Gombe State University of Science and Technology located in Gombe State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. GSUTECH was established in 2021 by the Gombe State Government as a specialized university focused on science, technology, engineering, and innovation. The institution was created to strengthen technological education and research in Nigeria. This page explains everything you need to know to increase your chances of gaining admission into GSUTECH.
Does Gombe State University of Science and Technology (GSUTECH) offer Chemical and Polymer Engineering?
No, Gombe State University of Science and Technology does not offer Chemical and Polymer Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Gombe State University of Science and Technology (GSUTECH) below to check if the Chemical and Polymer Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Chemical and Polymer Engineering When Accredited in Gombe State University of Science and Technology (GSUTECH)
O’Level Requirements
To study this course, candidates seeking admission into the Chemical and Polymer Engineering department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
GSUTECH Cut-Off Mark for Chemical and Polymer Engineering
The general UTME cut-off mark is 180, but due to the variation of Chemical and Polymer Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from GSUTECH Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other GSUTECH Science Courses with their Requirements
1. Software Engineering
To study this course, the minimum requirement for applicants seeking admission to the Software Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
two (2) other Science subjects.
2. Architecture
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
3. Computer Science (CS)
To study this course, candidates seeking admission into the Computer Science (CS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other Science subjects.
4. Physics
To study this course, candidates seeking admission into the Physics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Chemistry, Mathematics and
any other Science subject from
Biology / Agricultural Science.
5. Mathematics
To study this course, the minimum requirement for applicants seeking admission to the Mathematics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subjects.
6. Quantity Surveying (QS)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Quantity Surveying (QS) department.
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
7. Microbiology
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Microbiology department.
Nigerian Tertiary Institutions Offering Chemical and Polymer Engineering Course