If you are planning to study Metallurgical and Material Engineering at Gombe State University of Science and Technology located in Gombe State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. GSUTECH was established in 2021 by the Gombe State Government as a specialized university focused on science, technology, engineering, and innovation. The institution was created to strengthen technological education and research in Nigeria. This page explains everything you need to know to increase your chances of gaining admission into GSUTECH.
Does Gombe State University of Science and Technology (GSUTECH) offer Metallurgical and Material Engineering?
No, Gombe State University of Science and Technology does not offer Metallurgical and Material Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Gombe State University of Science and Technology (GSUTECH) below to check if the Metallurgical and Material Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Metallurgical and Material Engineering When Accredited in Gombe State University of Science and Technology (GSUTECH)
O’Level Requirements
To study this course, candidates seeking admission into the Metallurgical and Material Engineering department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
one other Science subject.
GSUTECH Cut-Off Mark for Metallurgical and Material Engineering
The general UTME cut-off mark is 180, but due to the variation of Metallurgical and Material Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from GSUTECH Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other GSUTECH Science Courses with their Requirements
1. Physics
To study this course, candidates aspiring to gain admission into Physics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Chemistry, Mathematics and
any other Science subject from
Biology / Agricultural Science.
2. Information System
To study this course, candidates aspiring to gain admission into Information System department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
three (3) other Science subjects.
3. Mathematics
To study this course, candidates seeking admission into the Mathematics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant subjects.
4. Chemistry
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Chemistry department.
5. Architecture
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
6. Quantity Surveying (QS)
To study this course, candidates seeking admission into the Quantity Surveying (QS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
7. Biology
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Biology department.
Mathematics / Physics and
any one other relevant subject.
Nigerian Universities Offering Metallurgical and Material Engineering Course