If you are planning to study Geography at Imo State University, Owerri located in Imo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. IMSU was established in 1981 by the Imo State Government following the creation of the state. The university was founded to provide quality higher education and has grown into one of the leading state universities in Nigeria. This page explains everything you need to know to increase your chances of gaining admission into IMSU.
Does Imo State University, Owerri (IMSU) offer Geography?
No, Imo State University, Owerri does not offer Geography under its Faculty of Earth and Mineral Sciences. However, since our course list is updated regularly, you can visit the courses available at Imo State University, Owerri (IMSU) below to check if the Geography course under the Faculty of Earth and Mineral Sciences has been updated.
Admission Requirements for Geography When Accredited in Imo State University, Owerri (IMSU)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Geography department under Faculty of Earth and Mineral Sciences, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other two (2) Science subjects.
JAMB Subject Combination
Mathematics, Biology, Chemistry,
Physics and Agricultural Science.
IMSU Cut-Off Mark for Geography
The general UTME cut-off mark is 180, but due to the variation of Geography cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from IMSU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other IMSU Science Courses with their Requirements
1. Quantity Surveying (QS)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Quantity Surveying (QS) department.
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
2. Crop Science and Biotechnology
To study this course, the minimum requirement for applicants seeking admission to the Crop Science and Biotechnology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology or Agricultural Science and
any other relevant subject.
3. Teacher Education Science
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Teacher Education Science department.
any two (2) other relevant subjects.
4. Building
To study this course, candidates seeking admission into the Building department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
5. Education and Mathematics
To study this course, candidates seeking admission into the Education and Mathematics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
one (1) other Science subject, and
any other relevant subjects.
6. Agricultural Engineering (AE)
To study this course, candidates seeking admission into the Agricultural Engineering (AE) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Any one other subject from:
Introduction to Agricultural Science,
Materials and Workshop Process and Machining,
Tractor Layout Power Unit Under Carriage and Auto Electricity;
Transmission System;
Implement and Machine;
Principles of Crop Husbandry and Land Use,
Materials and Workshop Processes;
Construction and Maintenance of Agricultural Machines;
General Metal Work;
General Wood Work and Building / Engineering Drawing.
7. Food Science and Technology (FT)
To study this course, candidates seeking admission into the Food Science and Technology (FT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Nigerian Universities Offering Geography Course