If you are planning to study Human Kinetics and Health Education at Institute of Management Technology, Enugu located in Enugu State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into IMT.
Does Institute of Management Technology, Enugu (IMT) offer Human Kinetics and Health Education?
No, Institute of Management Technology, Enugu does not offer Human Kinetics and Health Education under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Institute of Management Technology, Enugu (IMT) below to check if the Human Kinetics and Health Education course under the Faculty of Education has been updated.
Admission Requirements for Human Kinetics and Health Education When Accredited in Institute of Management Technology, Enugu (IMT)
O’Level Requirements
To study this course, candidates seeking admission into the Human Kinetics and Health Education department under Faculty of Education, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any three (3) other relevant subjects.
JAMB Subject Combination
any two (2) relevant subjects.
IMT Cut-Off Mark for Human Kinetics and Health Education
The general UTME cut-off mark is 230, but due to the variation of Human Kinetics and Health Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from IMT Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other IMT Science Courses with their Requirements
Building Technology (BT)
SSCE Requirements
To study this course, candidates seeking admission into the Building Technology (BT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Chemical Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Chemical Engineering Technology department.
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, Geography and Economics / Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Glass / Ceramics Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Glass / Ceramics Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science/Mathematics,
Biology/Agricultural Science, Woodwork,
Metalwork, Technical/Engineering Drawing,
Geography, Fine Art, Further Mathematics,
Fine Art, Economics Basic Electricity and
a minimum of pass grade in English Language.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Electrical / Electronic Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science Subject.
Civil Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Civil Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any one other subject from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Printing Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Printing Technology department.
any two (2) other subjects from:
Metal Work, Basic Electricity, Technical Drawing/Fine Art,
Book Keeping and Principles of Accounting, Economics/Commerce,
Statistics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Statistics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other relevant subject.
Nigerian Tertiary Institutions Offering Human Kinetics and Health Education Course