If you are planning to study Physical and Health Education at Institute of Management Technology, Enugu located in Enugu State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into IMT.
Does Institute of Management Technology, Enugu (IMT) offer Physical and Health Education?
No, Institute of Management Technology, Enugu does not offer Physical and Health Education under its Faculty of Health and Medical Sciences. However, since our course list is updated regularly, you can visit the courses available at Institute of Management Technology, Enugu (IMT) below to check if the Physical and Health Education course under the Faculty of Health and Medical Sciences has been updated.
Admission Requirements for Physical and Health Education When Accredited in Institute of Management Technology, Enugu (IMT)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Physical and Health Education department under Faculty of Health and Medical Sciences, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology or its equivalent
and any two (2) other relevant subjects.
JAMB Subject Combination
any two (2) relevant subjects.
IMT Cut-Off Mark for Physical and Health Education
The general UTME cut-off mark is 180, but due to the variation of Physical and Health Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from IMT Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other IMT Science Courses with their Requirements
Mechanical Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Engineering Technology department.
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Building Technology (BT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Science Laboratory Technology (SLT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Glass / Ceramics Technology
SSCE Requirements
To study this course, candidates seeking admission into the Glass / Ceramics Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science/Mathematics,
Biology/Agricultural Science, Woodwork,
Metalwork, Technical/Engineering Drawing,
Geography, Fine Art, Further Mathematics,
Fine Art, Economics Basic Electricity and
a minimum of pass grade in English Language.
Mechatronics Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechatronics Engineering Technology department.
and any one other subject from:
Biology / Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work,
Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics / Commerce.
Printing Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Printing Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other subjects from:
Metal Work, Basic Electricity, Technical Drawing/Fine Art,
Book Keeping and Principles of Accounting, Economics/Commerce,
Estate Management and Valuation
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Estate Management and Valuation department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Nigerian Tertiary Institutions Offering Physical and Health Education Course