Project Topics Seminar Topics Login Create Account
Search Topic
PARKLYN
ERVICES
 · RC: 2994849
Does IMT Offer Welding and Fabrication Technology | POLY Enquiry
WhatsApp Channel

Is Welding and Fabrication Technology Offered in Institute of Management Technology, Enugu (IMT)?

If you are planning to study Welding and Fabrication Technology at Institute of Management Technology, Enugu located in Enugu State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into IMT.

Does Institute of Management Technology, Enugu (IMT) offer Welding and Fabrication Technology?

No, Institute of Management Technology, Enugu does not offer Welding and Fabrication Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Institute of Management Technology, Enugu (IMT) below to check if the Welding and Fabrication Technology course under the Faculty of Engineering / Technology has been updated.

Admission Requirements for Welding and Fabrication Technology When Accredited in Institute of Management Technology, Enugu (IMT)

O’Level Requirements

To study this course, candidates aspiring to gain admission into Welding and Fabrication Technology department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:

  • Mathematics,

  • Physics,

  • Chemistry and

  • any two subjects from:

  • Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.

  • At least a credit pass in English Language is required.

JAMB Subject Combination

  • Use of English,

  • Mathematics and

  • Physics/Technical Drawing or Chemistry.

IMT Cut-Off Mark for Welding and Fabrication Technology

The general UTME cut-off mark is 180, but due to the variation of Welding and Fabrication Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from IMT Officials. However, to improve your admission chances:

  • Aim for 180+ score.

  • Perform well in Post-UTME screening.

Other IMT Science Courses with their Requirements

Chemical Engineering Technology

SSCE Requirements

To study this course, candidates aspiring to gain admission into Chemical Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:

  • English Language,

  • Mathematics,

  • Physics, Chemistry and

  • any other subject from:

  • Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, Geography and Economics / Commerce.

  • For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.

Quantity Surveying (QS)

SSCE Requirements

To study this course, the minimum requirement for applicants seeking admission to the Quantity Surveying (QS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:

  • English Language,

  • Mathematics,

  • Physics,

  • Chemistry and

  • any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.

Electrical / Electronic Engineering Technology

SSCE Requirements

To study this course, candidates aspiring to gain admission into Electrical / Electronic Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:

  • Mathematics,

  • Physics,

  • Chemistry,

  • English Language plus

  • any other Science Subject.

Printing Technology

SSCE Requirements

To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Printing Technology department.

  • English Language,

  • Mathematics,

  • Physics and

  • any two (2) other subjects from:

  • Metal Work, Basic Electricity, Technical Drawing/Fine Art,

  • Book Keeping and Principles of Accounting, Economics/Commerce,

Mechatronics Engineering Technology

SSCE Requirements

To study this course, candidates seeking admission into the Mechatronics Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:

  • English Language,

  • Mathematics,

  • Physics, Chemistry

  • and any one other subject from:

  • Biology / Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work,

  • Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics / Commerce.

Building Technology (BT)

SSCE Requirements

To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.

  • Mathematics,

  • English Language,

  • Physics, Chemistry and

  • any one of

  • Geography, Economics, Arts and Technical drawing.

  • For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.

Mechanical Engineering Technology

SSCE Requirements

To study this course, candidates seeking admission into the Mechanical Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:

  • English Language,

  • Mathematics,

  • Physics, Chemistry and

  • any one subject from:

  • Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce

  • For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.

Nigerian Polytechnics Offering Welding and Fabrication Technology Course

1
Delta State Polytechnic, Otefe Oghara
2
Delta State Polytechnic, Ugwashi-Uku
3
Gateway Polytechnic, Saapade
4
Yaba College of Technology (YABATECH)
5
Jigawa State Polytechnic