If you are planning to study Industrial Maintenance Engineering Technology at Jigawa State Polytechnic located in Jigawa State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Jigawa State Polytechnic.
Does Jigawa State Polytechnic offer Industrial Maintenance Engineering Technology?
No, Jigawa State Polytechnic does not offer Industrial Maintenance Engineering Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Jigawa State Polytechnic below to check if the Industrial Maintenance Engineering Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Industrial Maintenance Engineering Technology When Accredited in Jigawa State Polytechnic
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Industrial Maintenance Engineering Technology department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any one (1) of Biology/Agricultural Science.
Jigawa State Polytechnic Cut-Off Mark for Industrial Maintenance Engineering Technology
The general UTME cut-off mark is 180, but due to the variation of Industrial Maintenance Engineering Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Jigawa State Polytechnic Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Jigawa State Polytechnic Science Courses with their Requirements
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates seeking admission into the Science Laboratory Technology (SLT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Statistics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Statistics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other relevant subject.
Building Technology (BT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Electrical / Electronic Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science Subject.
Architectural Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architectural Technology department.
Biology, Fine Art, Chemistry, History, English Language, Geography, Further Mathematics, Economics / Commerce, Religious Knowledge, Technical Drawing and Business Method.
At least a pass in Fine Art or Technical Drawing.
Computer Science (CS)
SSCE Requirements
To study this course, candidates seeking admission into the Computer Science (CS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other Science subjects.
Welding and Fabrication Technology
SSCE Requirements
To study this course, candidates seeking admission into the Welding and Fabrication Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
Nigerian Tertiary Institutions Offering Industrial Maintenance Engineering Technology Course