If you are planning to study Health and Safety Education at Kaduna State University located in Kaduna State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. KASU was established in 2004 by the Kaduna State Government to expand access to higher education and promote research, innovation, and human capital development. This page explains everything you need to know to increase your chances of gaining admission into KASU.
Does Kaduna State University (KASU) offer Health and Safety Education?
No, Kaduna State University does not offer Health and Safety Education under its Faculty of Health and Medical Sciences. However, since our course list is updated regularly, you can visit the courses available at Kaduna State University (KASU) below to check if the Health and Safety Education course under the Faculty of Health and Medical Sciences has been updated.
Admission Requirements for Health and Safety Education When Accredited in Kaduna State University (KASU)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Health and Safety Education department under Faculty of Health and Medical Sciences, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any three (3) Science Subjects from:
JAMB Subject Combination
any two (2) Arts subjects.
KASU Cut-Off Mark for Health and Safety Education
The general UTME cut-off mark is 230, but due to the variation of Health and Safety Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KASU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KASU Science Courses with their Requirements
1. Agriculture
To study this course, candidates seeking admission into the Agriculture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science,
Mathematics / Physics, and
2. Medicine and Surgery
To study this course, candidates aspiring to gain admission into Medicine and Surgery department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
3. Building Technology (BT)
To study this course, candidates seeking admission into the Building Technology (BT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
4. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
5. Nursing (Science)
To study this course, candidates seeking admission into the Nursing (Science) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
6. Quantity Surveying (QS)
To study this course, the minimum requirement for applicants seeking admission to the Quantity Surveying (QS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
7. Mathematics
To study this course, the minimum requirement for applicants seeking admission to the Mathematics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subjects.
Nigerian Tertiary Institutions Offering Health and Safety Education Course