If you are planning to study Software Engineering at Kaduna State University located in Kaduna State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. KASU was established in 2004 by the Kaduna State Government to expand access to higher education and promote research, innovation, and human capital development. This page explains everything you need to know to increase your chances of gaining admission into KASU.
Does Kaduna State University (KASU) offer Software Engineering?
No, Kaduna State University does not offer Software Engineering under its Faculty of Data and Decision Sciences. However, since our course list is updated regularly, you can visit the courses available at Kaduna State University (KASU) below to check if the Software Engineering course under the Faculty of Data and Decision Sciences has been updated.
Admission Requirements for Software Engineering When Accredited in Kaduna State University (KASU)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Software Engineering department under Faculty of Data and Decision Sciences, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
two (2) other Science subjects.
JAMB Subject Combination
Biology, Chemistry, Agric Science, Economics and Geography.
KASU Cut-Off Mark for Software Engineering
The general UTME cut-off mark is 180, but due to the variation of Software Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KASU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KASU Science Courses with their Requirements
1. Chemistry
To study this course, candidates seeking admission into the Chemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
2. Mathematics
To study this course, candidates seeking admission into the Mathematics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant subjects.
3. Medicine and Surgery
To study this course, candidates aspiring to gain admission into Medicine and Surgery department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
4. Building Technology (BT)
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
5. Education and Mathematics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Education and Mathematics department.
one (1) other Science subject, and
any other relevant subjects.
6. Quantity Surveying (QS)
To study this course, candidates aspiring to gain admission into Quantity Surveying (QS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
7. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Nigerian Universities Offering Software Engineering Course