If you are planning to study Water Resources and Environmental Engineering at Kaduna State University located in Kaduna State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KASU.
Does Kaduna State University (KASU) offer Water Resources and Environmental Engineering?
No, Kaduna State University does not offer Water Resources and Environmental Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Kaduna State University (KASU) below to check if the Water Resources and Environmental Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Water Resources and Environmental Engineering When Accredited in Kaduna State University (KASU)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Water Resources and Environmental Engineering department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
KASU Cut-Off Mark for Water Resources and Environmental Engineering
The general UTME cut-off mark is 180, but due to the variation of Water Resources and Environmental Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KASU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KASU Science Courses with their Requirements
1. Building Technology (BT)
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
2. Geophysics
To study this course, candidates aspiring to gain admission into Geophysics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
3. Education and Chemistry
To study this course, candidates aspiring to gain admission into Education and Chemistry department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology and Agricultural Science.
4. Geology
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Geology department.
any other relevant subject.
5. Biotechnology
To study this course, candidates aspiring to gain admission into Biotechnology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
6. Quantity Surveying (QS)
To study this course, the minimum requirement for applicants seeking admission to the Quantity Surveying (QS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
7. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Nigerian Tertiary Institutions Offering Water Resources and Environmental Engineering Course