If you are planning to study Foundry Engineering Technology at Kano State Polytechnic located in Kano State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KANOPOLY.
Does Kano State Polytechnic (KANOPOLY) offer Foundry Engineering Technology?
No, Kano State Polytechnic does not offer Foundry Engineering Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Kano State Polytechnic (KANOPOLY) below to check if the Foundry Engineering Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Foundry Engineering Technology When Accredited in Kano State Polytechnic (KANOPOLY)
O’Level Requirements
To study this course, candidates seeking admission into the Foundry Engineering Technology department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
at least a pass in English Language,
any two relevant subjects from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
JAMB Subject Combination
Physics or Technical Drawing.
KANOPOLY Cut-Off Mark for Foundry Engineering Technology
The general UTME cut-off mark is 180, but due to the variation of Foundry Engineering Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KANOPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KANOPOLY Science Courses with their Requirements
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Statistics
SSCE Requirements
To study this course, candidates seeking admission into the Statistics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other relevant subject.
Textile Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Textile Technology department.
any other relevant subject from:
Biology/Agricultural Science,
Geography, Home Economics,
Fine Art, Economics/Commerce,
Clothing and Textile, Technical Drawing.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Electrical / Electronic Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science Subject.
Mechanical Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Surveying and Geoinformatics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates seeking admission into the Urban and Regional Planning (URP) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Nigerian Polytechnics Offering Foundry Engineering Technology Course