If you are planning to study Plant Science and Biotechnology at Kano State Polytechnic located in Kano State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KANOPOLY.
Does Kano State Polytechnic (KANOPOLY) offer Plant Science and Biotechnology?
No, Kano State Polytechnic does not offer Plant Science and Biotechnology under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Kano State Polytechnic (KANOPOLY) below to check if the Plant Science and Biotechnology course under the Faculty of Agriculture has been updated.
Admission Requirements for Plant Science and Biotechnology When Accredited in Kano State Polytechnic (KANOPOLY)
O’Level Requirements
To study this course, candidates seeking admission into the Plant Science and Biotechnology department under Faculty of Agriculture, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
JAMB Subject Combination
Including any other Science subject
KANOPOLY Cut-Off Mark for Plant Science and Biotechnology
The general UTME cut-off mark is 180, but due to the variation of Plant Science and Biotechnology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KANOPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KANOPOLY Science Courses with their Requirements
Computer Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Computer Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Mechanical Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Architectural Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architectural Technology department.
Biology, Fine Art, Chemistry, History, English Language, Geography, Further Mathematics, Economics / Commerce, Religious Knowledge, Technical Drawing and Business Method.
At least a pass in Fine Art or Technical Drawing.
Computer Science (CS)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Computer Science (CS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other Science subjects.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Electrical / Electronic Engineering Technology department.
any other Science Subject.
Welding and Fabrication Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Welding and Fabrication Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
Nigerian Tertiary Institutions Offering Plant Science and Biotechnology Course