If you are planning to study Chemical and Polymer Engineering at Kano State University of Science and Technology located in Kano State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KUST.
Does Kano State University of Science and Technology (KUST) offer Chemical and Polymer Engineering?
No, Kano State University of Science and Technology does not offer Chemical and Polymer Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Kano State University of Science and Technology (KUST) below to check if the Chemical and Polymer Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Chemical and Polymer Engineering When Accredited in Kano State University of Science and Technology (KUST)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Chemical and Polymer Engineering department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
KUST Cut-Off Mark for Chemical and Polymer Engineering
The general UTME cut-off mark is 180, but due to the variation of Chemical and Polymer Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KUST Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KUST Science Courses with their Requirements
Automotive Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Automotive Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
Biology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Biology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Mathematics / Physics and
any one other relevant subject.
Building Technology (BT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Information and Communication Technology (ICT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Information and Communication Technology (ICT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
two (2) other Science subjects.
Health Education
SSCE Requirements
To study this course, candidates seeking admission into the Health Education department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant subjects.
Computer Science (CS)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Computer Science (CS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other Science subjects.
Agricultural Engineering (AE)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Agricultural Engineering (AE) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Any one other subject from:
Introduction to Agricultural Science,
Materials and Workshop Process and Machining,
Tractor Layout Power Unit Under Carriage and Auto Electricity;
Transmission System;
Implement and Machine;
Principles of Crop Husbandry and Land Use,
Materials and Workshop Processes;
Construction and Maintenance of Agricultural Machines;
General Metal Work;
General Wood Work and Building / Engineering Drawing.
Nigerian Tertiary Institutions Offering Chemical and Polymer Engineering Course