If you are planning to study Mathematics and Education Technology at Kano State University of Science and Technology located in Kano State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KUST.
Does Kano State University of Science and Technology (KUST) offer Mathematics and Education Technology?
No, Kano State University of Science and Technology does not offer Mathematics and Education Technology under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Kano State University of Science and Technology (KUST) below to check if the Mathematics and Education Technology course under the Faculty of Education has been updated.
Admission Requirements for Mathematics and Education Technology When Accredited in Kano State University of Science and Technology (KUST)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Mathematics and Education Technology department under Faculty of Education, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
three (3) more pertinent science subjects in not more than two (2) sittings.
JAMB Subject Combination
one (1) other Science Subject.
KUST Cut-Off Mark for Mathematics and Education Technology
The general UTME cut-off mark is 180, but due to the variation of Mathematics and Education Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KUST Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KUST Science Courses with their Requirements
Architecture
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Agricultural Science and Education
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Agricultural Science and Education department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science,
any other relevant subject.
Geology
SSCE Requirements
To study this course, candidates seeking admission into the Geology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other relevant subject.
Civil Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Civil Engineering department.
Education and Mathematics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Education and Mathematics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
one (1) other Science subject, and
any other relevant subjects.
Forestry and Wildlife Management
SSCE Requirements
To study this course, candidates seeking admission into the Forestry and Wildlife Management department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Further Mathematics and Statistics.
Agricultural Engineering (AE)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Agricultural Engineering (AE) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any one other subject from:
Introduction to Agricultural Science,
Materials and Workshop Process and Machining,
Tractor Layout Power Unit Under Carriage and Auto Electricity;
Transmission System;
Implement and Machine;
Principles of Crop Husbandry and Land Use,
Materials and Workshop Processes;
Construction and Maintenance of Agricultural Machines;
General Metal Work;
General Wood Work and Building / Engineering Drawing.
Nigerian Tertiary Institutions Offering Mathematics and Education Technology Course