If you are planning to study Mechatronics Engineering Technology at Kano State University of Science and Technology located in Kano State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KUST.
Does Kano State University of Science and Technology (KUST) offer Mechatronics Engineering Technology?
No, Kano State University of Science and Technology does not offer Mechatronics Engineering Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Kano State University of Science and Technology (KUST) below to check if the Mechatronics Engineering Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechatronics Engineering Technology When Accredited in Kano State University of Science and Technology (KUST)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Mechatronics Engineering Technology department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
and any one other subject from:
Biology / Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work,
Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics / Commerce.
JAMB Subject Combination
Physics / Technical Drawing.
KUST Cut-Off Mark for Mechatronics Engineering Technology
The general UTME cut-off mark is 180, but due to the variation of Mechatronics Engineering Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KUST Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KUST Science Courses with their Requirements
1. Education and Integrated Science
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Education and Integrated Science department.
Any other four (4) relevant subjects
2. Automobile Technology Education
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Automobile Technology Education department.
Biology /Agricultural Science, Physics, or Chemistry and
two (2) from General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
3. Building Technology (BT)
To study this course, candidates seeking admission into the Building Technology (BT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
4. Forestry and Wildlife Management
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Forestry and Wildlife Management department.
Further Mathematics and Statistics.
5. Architecture
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
6. Agricultural Science and Education
To study this course, the minimum requirement for applicants seeking admission to the Agricultural Science and Education department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science,
any other relevant subject.
7. Agriculture
To study this course, candidates seeking admission into the Agriculture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science,
Mathematics / Physics, and
Nigerian Tertiary Institutions Offering Mechatronics Engineering Technology Course