If you are planning to study Natural Gas Engineering at Kano State University of Science and Technology located in Kano State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KUST.
Does Kano State University of Science and Technology (KUST) offer Natural Gas Engineering?
No, Kano State University of Science and Technology does not offer Natural Gas Engineering under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Kano State University of Science and Technology (KUST) below to check if the Natural Gas Engineering course under the Faculty of Science has been updated.
Admission Requirements for Natural Gas Engineering When Accredited in Kano State University of Science and Technology (KUST)
O’Level Requirements
To study this course, candidates seeking admission into the Natural Gas Engineering department under Faculty of Science, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
and any one Science subject.
KUST Cut-Off Mark for Natural Gas Engineering
The general UTME cut-off mark is 180, but due to the variation of Natural Gas Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KUST Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KUST Science Courses with their Requirements
Education and Mathematics
SSCE Requirements
To study this course, candidates seeking admission into the Education and Mathematics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
one (1) other Science subject, and
any other relevant subjects.
Mathematics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mathematics department.
any two (2) other relevant subjects.
Building Technology (BT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Food Science and Technology (FT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Food Science and Technology (FT) department.
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Fisheries and Aquaculture
SSCE Requirements
To study this course, candidates seeking admission into the Fisheries and Aquaculture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science,
Physics/Geography/Economics.
Electrical / Electronics Education
SSCE Requirements
To study this course, candidates aspiring to gain admission into Electrical / Electronics Education department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
Agricultural Engineering (AE)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Agricultural Engineering (AE) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any one other subject from:
Introduction to Agricultural Science,
Materials and Workshop Process and Machining,
Tractor Layout Power Unit Under Carriage and Auto Electricity;
Transmission System;
Implement and Machine;
Principles of Crop Husbandry and Land Use,
Materials and Workshop Processes;
Construction and Maintenance of Agricultural Machines;
General Metal Work;
General Wood Work and Building / Engineering Drawing.
Nigerian Tertiary Institutions Offering Natural Gas Engineering Course