If you are planning to study Glass Technology at Kebbi State University of Science and Technology located in Kebbi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. KSUSTA was established in 2006 by the Kebbi State Government to advance science, technology, and innovation through quality higher education and research. This page explains everything you need to know to increase your chances of gaining admission into KSUSTA.
Does Kebbi State University of Science and Technology (KSUSTA) offer Glass Technology?
No, Kebbi State University of Science and Technology does not offer Glass Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Kebbi State University of Science and Technology (KSUSTA) below to check if the Glass Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Glass Technology When Accredited in Kebbi State University of Science and Technology (KSUSTA)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Glass Technology department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing, Ceramics, Graphic Design, Graphic Printing, Decorative Painting,
Spray Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Building / Engineering Drawing, General Wood Work.
KSUSTA Cut-Off Mark for Glass Technology
The general UTME cut-off mark is 180, but due to the variation of Glass Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KSUSTA Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KSUSTA Science Courses with their Requirements
1. Medicine and Surgery
To study this course, candidates seeking admission into the Medicine and Surgery department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
2. Agriculture
To study this course, candidates aspiring to gain admission into Agriculture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science,
Mathematics / Physics, and
3. Biochemistry
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Biochemistry department.
4. Woodwork Technology Education
To study this course, candidates seeking admission into the Woodwork Technology Education department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any one (1) of Biology / Agricultural Science, Physics, or Chemistry and
two (2) from General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
5. Quantity Surveying (QS)
To study this course, candidates seeking admission into the Quantity Surveying (QS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
6. Education and Mathematics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Education and Mathematics department.
one (1) other Science subject, and
any other relevant subjects.
7. Biology
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Biology department.
Mathematics / Physics and
any one other relevant subject.
Nigerian Tertiary Institutions Offering Glass Technology Course