	PARKLYN ERVICES	·	RC: 2994849

Does KSUSTA Offer Mechanical Metalwork Technology Education | UNI Enquiry

facebook Page

WhatsApp Channel

Is Mechanical Metalwork Technology Education Offered in Kebbi State University of Science and Technology (KSUSTA)?

If you are planning to study Mechanical Metalwork Technology Education at Kebbi State University of Science and Technology located in Kebbi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KSUSTA.

Does Kebbi State University of Science and Technology (KSUSTA) offer Mechanical Metalwork Technology Education?

No, Kebbi State University of Science and Technology does not offer Mechanical Metalwork Technology Education under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Kebbi State University of Science and Technology (KSUSTA) below to check if the Mechanical Metalwork Technology Education course under the Faculty of Engineering / Technology has been updated.

Admission Requirements for Mechanical Metalwork Technology Education When Accredited in Kebbi State University of Science and Technology (KSUSTA)

O’Level Requirements

To study this course, candidates aspiring to gain admission into Mechanical Metalwork Technology Education department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:

English Language,
Mathematics,
one (1) of Biology /Agricultural Science; Physics, or Chemistry and
two (2) from General Science/IntegratedScience, Technical Drawing/Fine Art, Health Science Food and Nutrition,
Geography, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.

JAMB Subject Combination

Use of English,
Mathematics,
Physics and
any other relevant subject.

KSUSTA Cut-Off Mark for Mechanical Metalwork Technology Education

The general UTME cut-off mark is 180, but due to the variation of Mechanical Metalwork Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KSUSTA Officials. However, to improve your admission chances:

Aim for 180+ score.
Perform well in Post-UTME screening.

Other KSUSTA Science Courses with their Requirements

Architecture

SSCE Requirements

To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:

English Language,
Physics,
Mathematics, and
any one (1) of
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity

Quantity Surveying (QS)

SSCE Requirements

To study this course, candidates seeking admission into the Quantity Surveying (QS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:

English Language,
Mathematics,
Physics,
Chemistry and
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.

Building

SSCE Requirements

To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building department.

Mathematics,
English Language,
Physics, Chemistry,
and any one of
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.

Geography

SSCE Requirements

To study this course, candidates aspiring to gain admission into Geography department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:

English Language,
Mathematics,
Geography and
any other two (2) Science subjects.

Education and Physics

SSCE Requirements

To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Education and Physics department.

English Language,
Physics,
Mathematics, and
two (2) other Science subjects or NTC / NBC.

Agricultural Science (Double Major)

SSCE Requirements

To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Agricultural Science (Double Major) department.

English Language,
Chemistry,
Biology / Agricultural Science,
Mathematics and
another relevant subject.

Microbiology

SSCE Requirements

To study this course, candidates aspiring to gain admission into Microbiology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:

English Language,
Mathematics,
Chemistry,
Biology and
Physics.

Nigerian Tertiary Institutions Offering Mechanical Metalwork Technology Education Course

Ebonyi State University (EBSU)

Kindly check back later for update on more schools offering Mechanical Metalwork Technology Education courses