If you are planning to study Mechatronics Engineering at Kebbi State University of Science and Technology located in Kebbi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KSUSTA.
Does Kebbi State University of Science and Technology (KSUSTA) offer Mechatronics Engineering?
No, Kebbi State University of Science and Technology does not offer Mechatronics Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Kebbi State University of Science and Technology (KSUSTA) below to check if the Mechatronics Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechatronics Engineering When Accredited in Kebbi State University of Science and Technology (KSUSTA)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechatronics Engineering department under Faculty of Engineering / Technology.
any other Science subject.
KSUSTA Cut-Off Mark for Mechatronics Engineering
The general UTME cut-off mark is 180, but due to the variation of Mechatronics Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KSUSTA Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KSUSTA Science Courses with their Requirements
1. Education and Biology
To study this course, candidates seeking admission into the Education and Biology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
2. Metalwork / Woodwork Technology Education
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Metalwork / Woodwork Technology Education department.
Physics / Chemistry, Biology or Agricultural Science;
Physics / Chemistry, Biology or Agricultural Science;
General Science / Integrated Science, Technical Drawing / Fine Art, Health Science Food and Nutrition, Geography, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
3. Quantity Surveying (QS)
To study this course, candidates aspiring to gain admission into Quantity Surveying (QS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
4. Woodwork Technology Education
To study this course, candidates seeking admission into the Woodwork Technology Education department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any one (1) of Biology / Agricultural Science, Physics, or Chemistry and
two (2) from General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
5. Applied Chemistry
To study this course, candidates seeking admission into the Applied Chemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
6. Computer Science (CS)
To study this course, candidates seeking admission into the Computer Science (CS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other Science subjects.
7. Nursing (Science)
To study this course, candidates aspiring to gain admission into Nursing (Science) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Nigerian Universities Offering Mechatronics Engineering Course