If you are planning to study Mechatronics Engineering Technology at Kebbi State University of Science and Technology located in Kebbi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. KSUSTA was established in 2006 by the Kebbi State Government to advance science, technology, and innovation through quality higher education and research. This page explains everything you need to know to increase your chances of gaining admission into KSUSTA.
Does Kebbi State University of Science and Technology (KSUSTA) offer Mechatronics Engineering Technology?
No, Kebbi State University of Science and Technology does not offer Mechatronics Engineering Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Kebbi State University of Science and Technology (KSUSTA) below to check if the Mechatronics Engineering Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechatronics Engineering Technology When Accredited in Kebbi State University of Science and Technology (KSUSTA)
O’Level Requirements
To study this course, candidates seeking admission into the Mechatronics Engineering Technology department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
and any one other subject from:
Biology / Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work,
Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics / Commerce.
JAMB Subject Combination
Physics / Technical Drawing.
KSUSTA Cut-Off Mark for Mechatronics Engineering Technology
The general UTME cut-off mark is 180, but due to the variation of Mechatronics Engineering Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KSUSTA Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KSUSTA Science Courses with their Requirements
1. Botany
To study this course, the minimum requirement for applicants seeking admission to the Botany department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
2. Automobile Technology Education
To study this course, candidates seeking admission into the Automobile Technology Education department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology /Agricultural Science, Physics, or Chemistry and
two (2) from General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
3. Urban and Regional Planning (URP)
To study this course, candidates aspiring to gain admission into Urban and Regional Planning (URP) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
4. Fisheries
To study this course, the minimum requirement for applicants seeking admission to the Fisheries department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science,
any other Science subject.
5. Architecture
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
6. Education and Physics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Education and Physics department.
two (2) other Science subjects or NTC / NBC.
7. Woodwork Technology Education
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Woodwork Technology Education department.
any one (1) of Biology / Agricultural Science, Physics, or Chemistry and
two (2) from General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
Nigerian Tertiary Institutions Offering Mechatronics Engineering Technology Course