If you are planning to study Animal and Environmental Biology at Kwara State Polytechnic located in Kwara State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KWARAPOLY.
Does Kwara State Polytechnic (KWARAPOLY) offer Animal and Environmental Biology?
No, Kwara State Polytechnic does not offer Animal and Environmental Biology under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Kwara State Polytechnic (KWARAPOLY) below to check if the Animal and Environmental Biology course under the Faculty of Science has been updated.
Admission Requirements for Animal and Environmental Biology When Accredited in Kwara State Polytechnic (KWARAPOLY)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Animal and Environmental Biology department under Faculty of Science, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
two (2) other Science subject.
JAMB Subject Combination
Physics, Chemistry and Mathematics.
KWARAPOLY Cut-Off Mark for Animal and Environmental Biology
The general UTME cut-off mark is 180, but due to the variation of Animal and Environmental Biology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KWARAPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KWARAPOLY Science Courses with their Requirements
Agricultural Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Agricultural Technology department.
Biology / Agricultural Science,
Mathematics, Chemistry and
Geography, Food and Nutrition, Economics,
Technical Drawing, Physics, Nigerian Language and Home Economics.
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Architectural Technology
SSCE Requirements
To study this course, candidates seeking admission into the Architectural Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology, Fine Art, Chemistry, History, English Language, Geography, Further Mathematics, Economics / Commerce, Religious Knowledge, Technical Drawing and Business Method.
At least a pass in Fine Art or Technical Drawing.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Urban and Regional Planning (URP) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Electrical / Electronic Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science Subject.
Metallurgical Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Metallurgical Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work,
Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
Welding and Fabrication Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Welding and Fabrication Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
Nigerian Tertiary Institutions Offering Animal and Environmental Biology Course