If you are planning to study Polymer Technology at Kwara State Polytechnic located in Kwara State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KWARAPOLY.
Does Kwara State Polytechnic (KWARAPOLY) offer Polymer Technology?
No, Kwara State Polytechnic does not offer Polymer Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Kwara State Polytechnic (KWARAPOLY) below to check if the Polymer Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Polymer Technology When Accredited in Kwara State Polytechnic (KWARAPOLY)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Polymer Technology department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
KWARAPOLY Cut-Off Mark for Polymer Technology
The general UTME cut-off mark is 180, but due to the variation of Polymer Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KWARAPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KWARAPOLY Science Courses with their Requirements
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Agricultural Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Agricultural Technology department.
Biology / Agricultural Science,
Mathematics, Chemistry and
Geography, Food and Nutrition, Economics,
Technical Drawing, Physics, Nigerian Language and Home Economics.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Science Laboratory Technology (SLT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Mineral Resources Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mineral Resources Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any one (1) subject from:
Biology/Agricultural Science,
Basic Electronics/Basic Electricity, Auto Mechanics,
Metal Work, Woodwork for Civil Engineering Technology,
Further Mathematics, English Language, Geography, Economics/Commerce.
Computer Science (CS)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Computer Science (CS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other Science subjects.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Urban and Regional Planning (URP) department.
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Welding and Fabrication Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Welding and Fabrication Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
Nigerian Tertiary Institutions Offering Polymer Technology Course