If you are planning to study Industrial Engineering at Lagos State University of Science and Technology formally known as Lagos State Polytechnic located in Lagos State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. LASUSTECH was established in 2022 by the Lagos State Government as part of a higher education reform that converted existing institutions into a university focused on science and technology education. This page explains everything you need to know to increase your chances of gaining admission into LASUSTECH.
Does Lagos State University of Science and Technology offer Industrial Engineering?
No, Lagos State University of Science and Technology does not offer Industrial Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Lagos State University of Science and Technology below to check if the Industrial Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Industrial Engineering When Accredited in Lagos State University of Science and Technology
O’Level Requirements
To study this course, candidates aspiring to gain admission into Industrial Engineering department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
LASUSTECH Cut-Off Mark for Industrial Engineering
The general UTME cut-off mark is 180, but due to the variation of Industrial Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from LASUSTECH Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other LASUSTECH Science Courses with their Requirements
1. Agricultural Engineering / Technology
To study this course, the minimum requirement for applicants seeking admission to the Agricultural Engineering / Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any three of the following:
Biology / Agricultural Science, Chemistry, Technical Drawing, Basic Electronics / Basic Electricity, Auto Mechanics, Metal Work, Further Mathematics, Food and Nutrition and Geography.
At least passes in Chemistry, Biology / Agricultural Science / Food and Nutrition.
2. Building Technology (BT)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
3. Urban and Regional Planning (URP)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Urban and Regional Planning (URP) department.
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
4. Science Laboratory Technology (SLT)
To study this course, candidates seeking admission into the Science Laboratory Technology (SLT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
5. Horticultural Technology
To study this course, the minimum requirement for applicants seeking admission to the Horticultural Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other relevant subjectes.
6. Chemical Engineering Technology
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Chemical Engineering Technology department.
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, Geography and Economics / Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
7. Mechanical Engineering Technology
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Nigerian Tertiary Institutions Offering Industrial Engineering Course