If you are planning to study Prosthesis and Orthopaedic Technology at Lead City University, Ibadan located in Oyo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Lead City University was established in 2005 as a private university in Ibadan, Oyo State, to provide access to quality higher education with focus on innovation, research, and moral development. This page explains everything you need to know to increase your chances of gaining admission into Lead City University.
Does Lead City University, Ibadan (LCU) offer Prosthesis and Orthopaedic Technology?
No, Lead City University, Ibadan does not offer Prosthesis and Orthopaedic Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Lead City University, Ibadan (LCU) below to check if the Prosthesis and Orthopaedic Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Prosthesis and Orthopaedic Technology When Accredited in Lead City University, Ibadan (LCU)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Prosthesis and Orthopaedic Technology department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Lead City University Cut-Off Mark for Prosthesis and Orthopaedic Technology
The general UTME cut-off mark is 180, but due to the variation of Prosthesis and Orthopaedic Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Lead City University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Lead City University Science Courses with their Requirements
1. Architecture
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
2. Education and Chemistry
To study this course, the minimum requirement for applicants seeking admission to the Education and Chemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology and Agricultural Science.
3. Science Laboratory Technology (SLT)
To study this course, candidates seeking admission into the Science Laboratory Technology (SLT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
4. Education and Physics
To study this course, candidates seeking admission into the Education and Physics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subjects or NTC / NBC.
5. Anatomy
To study this course, candidates aspiring to gain admission into Anatomy department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
6. Physiology
To study this course, the minimum requirement for applicants seeking admission to the Physiology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
7. Computer with Electronics
To study this course, candidates seeking admission into the Computer with Electronics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other two (2) Science subjects.
Nigerian Tertiary Institutions Offering Prosthesis and Orthopaedic Technology Course