If you are planning to study Biological Sciences and Engineering at Modibbo Adama University Of Technology located in Adamawa State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into MAUTECH.
Does Modibbo Adama University Of Technology (MAUTECH) offer Biological Sciences and Engineering?
No, Modibbo Adama University Of Technology does not offer Biological Sciences and Engineering under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Modibbo Adama University Of Technology (MAUTECH) below to check if the Biological Sciences and Engineering course under the Faculty of Science has been updated.
Admission Requirements for Biological Sciences and Engineering When Accredited in Modibbo Adama University Of Technology (MAUTECH)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Biological Sciences and Engineering department under Faculty of Science, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
MAUTECH Cut-Off Mark for Biological Sciences and Engineering
The general UTME cut-off mark is 180, but due to the variation of Biological Sciences and Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from MAUTECH Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other MAUTECH Science Courses with their Requirements
1. Building
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
2. Urban and Regional Planning (URP)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Urban and Regional Planning (URP) department.
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
3. Technology and Vocational Education
To study this course, candidates seeking admission into the Technology and Vocational Education department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any three (3) other relevant subjects.
4. Science Laboratory Technology (SLT)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Science Laboratory Technology (SLT) department.
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
5. Geography
To study this course, candidates aspiring to gain admission into Geography department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other two (2) Science subjects.
6. Agricultural and Environmental Engineering
To study this course, candidates aspiring to gain admission into Agricultural and Environmental Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Introduction to Agricultural Science, Materials and Workshop Process and Machining,
Tractor Layout Power Unit Under Carriage and Auto Electricity, Transmission System, Implement and Machine,
Principles of Crop Husbandry and Land Use, Materials and Workshop Processes,
Construction and Maintenance of Agricultural Machines, general Metal Work, General Wood Work and Building/Engineering Drawing.
7. Medicine and Surgery
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Medicine and Surgery department.
Nigerian Tertiary Institutions Offering Biological Sciences and Engineering Course