If you are planning to study Education and Science at Modibbo Adama University Of Technology located in Adamawa State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. MAUTECH was established in 1981 as a federal university of technology in Yola, Adamawa State, to advance science, engineering, and technological education in Nigeria. This page explains everything you need to know to increase your chances of gaining admission into MAUTECH.
Does Modibbo Adama University Of Technology (MAUTECH) offer Education and Science?
No, Modibbo Adama University Of Technology does not offer Education and Science under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Modibbo Adama University Of Technology (MAUTECH) below to check if the Education and Science course under the Faculty of Education has been updated.
Admission Requirements for Education and Science When Accredited in Modibbo Adama University Of Technology (MAUTECH)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Education and Science department under Faculty of Education, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
two (2) other Science subjects and
any other relevant subjectes.
JAMB Subject Combination
any Three (3) relevant Science or NBC subjects.
MAUTECH Cut-Off Mark for Education and Science
The general UTME cut-off mark is 180, but due to the variation of Education and Science cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from MAUTECH Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other MAUTECH Science Courses with their Requirements
1. Information Technology
To study this course, the minimum requirement for applicants seeking admission to the Information Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subjects.
2. Mathematics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mathematics department.
any two (2) other relevant subjects.
3. Fisheries and Aquaculture
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Fisheries and Aquaculture department.
Biology/Agricultural Science,
Physics/Geography/Economics.
4. Fisheries
To study this course, the minimum requirement for applicants seeking admission to the Fisheries department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science,
any other Science subject.
5. Surveying and Geoinformatics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
6. Industrial Chemistry
To study this course, candidates seeking admission into the Industrial Chemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science.
7. Building
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Nigerian Universities Offering Education and Science Course