If you are planning to study Orthopaedic and Plaster Technology at Isa Mustapha Agwai Polytechnic, Lafia formally known as Nasarawa State Polytechnic, Lafia located in Nasawara State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into IMAPOLY.
Does Isa Mustapha Agwai Polytechnic, Lafia offer Orthopaedic and Plaster Technology?
No, Isa Mustapha Agwai Polytechnic, Lafia does not offer Orthopaedic and Plaster Technology under its Faculty of Allied Health Sciences. However, since our course list is updated regularly, you can visit the courses available at Isa Mustapha Agwai Polytechnic, Lafia below to check if the Orthopaedic and Plaster Technology course under the Faculty of Allied Health Sciences has been updated.
Admission Requirements for Orthopaedic and Plaster Technology When Accredited in Isa Mustapha Agwai Polytechnic, Lafia
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Orthopaedic and Plaster Technology department under Faculty of Allied Health Sciences.
IMAPOLY Cut-Off Mark for Orthopaedic and Plaster Technology
The general UTME cut-off mark is 230, but due to the variation of Orthopaedic and Plaster Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from IMAPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other IMAPOLY Science Courses with their Requirements
Estate Management and Valuation
SSCE Requirements
To study this course, candidates seeking admission into the Estate Management and Valuation department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Electrical / Electronic Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science Subject.
Statistics
SSCE Requirements
To study this course, candidates seeking admission into the Statistics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other relevant subject.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Science Laboratory Technology (SLT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Building Technology (BT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates seeking admission into the Urban and Regional Planning (URP) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Architectural Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Architectural Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology, Fine Art, Chemistry, History, English Language, Geography, Further Mathematics, Economics / Commerce, Religious Knowledge, Technical Drawing and Business Method.
At least a pass in Fine Art or Technical Drawing.
Nigerian Tertiary Institutions Offering Orthopaedic and Plaster Technology Course