If you are planning to study Animal Breeding and Genetics at Nnamdi Azikiwe University located in Anambra State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into UNIZIK.
Does Nnamdi Azikiwe University (UNIZIK) offer Animal Breeding and Genetics?
No, Nnamdi Azikiwe University does not offer Animal Breeding and Genetics under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Nnamdi Azikiwe University (UNIZIK) below to check if the Animal Breeding and Genetics course under the Faculty of Agriculture has been updated.
Admission Requirements for Animal Breeding and Genetics When Accredited in Nnamdi Azikiwe University (UNIZIK)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Animal Breeding and Genetics department under Faculty of Agriculture.
JAMB Subject Combination
Biology / Agriculture and
UNIZIK Cut-Off Mark for Animal Breeding and Genetics
The general UTME cut-off mark is 180, but due to the variation of Animal Breeding and Genetics cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from UNIZIK Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other UNIZIK Science Courses with their Requirements
Building
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Technical Education
SSCE Requirements
To study this course, candidates aspiring to gain admission into Technical Education department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any three (3) relevant subjects.
Metallurgical and Material Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Metallurgical and Material Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
one other Science subject.
Surveying and Geoinformatics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Geography and Meteorology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Geography and Meteorology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Arts or Social Science subjects with at least a pass in Mathematics.
Mathematics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mathematics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subjects.
Electronics and Computer Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Electronics and Computer Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other one (1) relevant subject.
Nigerian Tertiary Institutions Offering Animal Breeding and Genetics Course