If you are planning to study Environmental Management and Pollution Control at Nnamdi Azikiwe University located in Anambra State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. UNIZIK was originally established in 1991 by the Anambra State Government as a tertiary institution for higher education. It was upgraded to a full university in 1992 and has since grown into one of Nigeria’s leading federal universities. This page explains everything you need to know to increase your chances of gaining admission into UNIZIK.
Does Nnamdi Azikiwe University (UNIZIK) offer Environmental Management and Pollution Control?
No, Nnamdi Azikiwe University does not offer Environmental Management and Pollution Control under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Nnamdi Azikiwe University (UNIZIK) below to check if the Environmental Management and Pollution Control course under the Faculty of Science has been updated.
Admission Requirements for Environmental Management and Pollution Control When Accredited in Nnamdi Azikiwe University (UNIZIK)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Environmental Management and Pollution Control department under Faculty of Science, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
UNIZIK Cut-Off Mark for Environmental Management and Pollution Control
The general UTME cut-off mark is 180, but due to the variation of Environmental Management and Pollution Control cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from UNIZIK Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other UNIZIK Science Courses with their Requirements
1. Chemical Engineering
To study this course, the minimum requirement for applicants seeking admission to the Chemical Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
2. Mechanical Engineering
To study this course, candidates seeking admission into the Mechanical Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant Science subjects.
3. Geological Sciences
To study this course, candidates seeking admission into the Geological Sciences department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other relevant subject.
4. Auto and Mechanical Technology Education
To study this course, candidates aspiring to gain admission into Auto and Mechanical Technology Education department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any one (1) of Biology / Agricultural Science; Physics, or Chemistry,
Auto Technical, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition,
Physical and Health Education, General Science / Integrated Science, Building, Electrical Electronic, Metal Work and Wood Work.
5. Human Kinetics
To study this course, candidates seeking admission into the Human Kinetics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Health Science / Physical Education / Biology
Any other two (2) relevant subjects
6. Quantity Surveying (QS)
To study this course, the minimum requirement for applicants seeking admission to the Quantity Surveying (QS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
7. Agricultural and Bioresources Engineering
To study this course, candidates seeking admission into the Agricultural and Bioresources Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Introduction to Agricultural Science, Materials and Workshop Process and Machining, Tractor Layout Power Unit Under Carriage and Auto Electricity; Transmission System; Implement and Machine;
Principles of Crop Husbandry and Land Use, Materials and Workshop Processes; Construction and Maintenance of Agricultural Machines; General Metal Work; General Wood Work and Building / Engineering Drawing.
Nigerian Tertiary Institutions Offering Environmental Management and Pollution Control Course