If you are planning to study Wildlife Management at Nnamdi Azikiwe University located in Anambra State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into UNIZIK.
Does Nnamdi Azikiwe University (UNIZIK) offer Wildlife Management?
No, Nnamdi Azikiwe University does not offer Wildlife Management under its Faculty of Renewable and Natural Resources. However, since our course list is updated regularly, you can visit the courses available at Nnamdi Azikiwe University (UNIZIK) below to check if the Wildlife Management course under the Faculty of Renewable and Natural Resources has been updated.
Admission Requirements for Wildlife Management When Accredited in Nnamdi Azikiwe University (UNIZIK)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Wildlife Management department under Faculty of Renewable and Natural Resources.
Biology / Agricultural Science,
any one (1) of Geography, Physics and Economics.
JAMB Subject Combination
Biology / Agricultural Science.
UNIZIK Cut-Off Mark for Wildlife Management
The general UTME cut-off mark is 180, but due to the variation of Wildlife Management cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from UNIZIK Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other UNIZIK Science Courses with their Requirements
Architecture
SSCE Requirements
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Polymer and Textile Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Polymer and Textile Engineering department.
any other Science subject.
Metallurgical and Material Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Metallurgical and Material Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
one other Science subject.
Physical and Health Education
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Physical and Health Education department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology or its equivalent
and any two (2) other relevant subjects.
Building and Woodwork Technology Education
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building and Woodwork Technology Education department.
any other Science subject.
Teacher Education Science
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Teacher Education Science department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subjects.
Agricultural and Bioresources Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Agricultural and Bioresources Engineering department.
Introduction to Agricultural Science, Materials and Workshop Process and Machining, Tractor Layout Power Unit Under Carriage and Auto Electricity; Transmission System; Implement and Machine;
Principles of Crop Husbandry and Land Use, Materials and Workshop Processes; Construction and Maintenance of Agricultural Machines; General Metal Work; General Wood Work and Building / Engineering Drawing.
Nigerian Tertiary Institutions Offering Wildlife Management Course