If you are planning to study Metallurgical Engineering at Obafemi Awolowo University located in Osun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into OAU.
Does Obafemi Awolowo University (OAU) offer Metallurgical Engineering?
No, Obafemi Awolowo University does not offer Metallurgical Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Obafemi Awolowo University (OAU) below to check if the Metallurgical Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Metallurgical Engineering When Accredited in Obafemi Awolowo University (OAU)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Metallurgical Engineering department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
one other Science subject.
OAU Cut-Off Mark for Metallurgical Engineering
The general UTME cut-off mark is 180, but due to the variation of Metallurgical Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from OAU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other OAU Science Courses with their Requirements
Industrial Chemistry
SSCE Requirements
To study this course, candidates aspiring to gain admission into Industrial Chemistry department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science.
Metallurgical and Material Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Metallurgical and Material Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
one other Science subject.
Food Science and Technology (FT)
SSCE Requirements
To study this course, candidates seeking admission into the Food Science and Technology (FT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Nutrition and Consumers Services
SSCE Requirements
To study this course, candidates seeking admission into the Nutrition and Consumers Services department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science,
Mathematics, Chemistry, Physics,
Nutrition, Fine Arts, Textile, Construction,
Technical Drawing, Basic Electricity, Basic Catering and Food Services,
Bakery and Confectioneries, General Metal Work,
Bleaching, Dyeing and Finishing, Ladies Garment Construction and Finishing,
Men Garment Construction and Finishing, Spinning, Weaving, Surface Design and Printing.
Chemical Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Chemical Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
Architecture
SSCE Requirements
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Medicine and Surgery
SSCE Requirements
To study this course, candidates seeking admission into the Medicine and Surgery department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Nigerian Tertiary Institutions Offering Metallurgical Engineering Course