If you are planning to study Prosthesis and Orthopaedic Technology at Oduduwa University located in Osun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Oduduwa University was established in 2009 as a private university in Osun State to promote quality higher education with strong emphasis on cultural values, entrepreneurship, and academic excellence. This page explains everything you need to know to increase your chances of gaining admission into Oduduwa University.
Does Oduduwa University (OUI) offer Prosthesis and Orthopaedic Technology?
No, Oduduwa University does not offer Prosthesis and Orthopaedic Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Oduduwa University (OUI) below to check if the Prosthesis and Orthopaedic Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Prosthesis and Orthopaedic Technology When Accredited in Oduduwa University (OUI)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Prosthesis and Orthopaedic Technology department under Faculty of Engineering / Technology.
Oduduwa University Cut-Off Mark for Prosthesis and Orthopaedic Technology
The general UTME cut-off mark is 180, but due to the variation of Prosthesis and Orthopaedic Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Oduduwa University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Oduduwa University Science Courses with their Requirements
1. Mechanical Engineering
To study this course, candidates aspiring to gain admission into Mechanical Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant Science subjects.
2. Computer Science (CS)
To study this course, candidates seeking admission into the Computer Science (CS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other Science subjects.
3. Microbiology
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Microbiology department.
4. Biochemistry
To study this course, candidates seeking admission into the Biochemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
5. Mathematics With Statistics
To study this course, candidates aspiring to gain admission into Mathematics With Statistics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology and Additional / Further Mathematics.
6. Chemical Engineering Technology
To study this course, candidates aspiring to gain admission into Chemical Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, Geography and Economics / Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
7. Quantity Surveying (QS)
To study this course, the minimum requirement for applicants seeking admission to the Quantity Surveying (QS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
Nigerian Tertiary Institutions Offering Prosthesis and Orthopaedic Technology Course