If you are planning to study Orthopaedic and Plaster Technology at Plateau State Polytechnic, Barkin-Ladi located in Plateau State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into PLAPOLY.
Does Plateau State Polytechnic, Barkin-Ladi (PLAPOLY) offer Orthopaedic and Plaster Technology?
No, Plateau State Polytechnic, Barkin-Ladi does not offer Orthopaedic and Plaster Technology under its Faculty of Allied Health Sciences. However, since our course list is updated regularly, you can visit the courses available at Plateau State Polytechnic, Barkin-Ladi (PLAPOLY) below to check if the Orthopaedic and Plaster Technology course under the Faculty of Allied Health Sciences has been updated.
Admission Requirements for Orthopaedic and Plaster Technology When Accredited in Plateau State Polytechnic, Barkin-Ladi (PLAPOLY)
O’Level Requirements
To study this course, candidates seeking admission into the Orthopaedic and Plaster Technology department under Faculty of Allied Health Sciences, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
PLAPOLY Cut-Off Mark for Orthopaedic and Plaster Technology
The general UTME cut-off mark is 230, but due to the variation of Orthopaedic and Plaster Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from PLAPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other PLAPOLY Science Courses with their Requirements
Mineral Resources Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Mineral Resources Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any one (1) subject from:
Biology/Agricultural Science,
Basic Electronics/Basic Electricity, Auto Mechanics,
Metal Work, Woodwork for Civil Engineering Technology,
Further Mathematics, English Language, Geography, Economics/Commerce.
Computer Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Computer Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Building Technology (BT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Metallurgical Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Metallurgical Engineering Technology department.
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work,
Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
Mechanical Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Agricultural Engineering / Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Agricultural Engineering / Technology department.
any three of the following:
Biology / Agricultural Science, Chemistry, Technical Drawing, Basic Electronics / Basic Electricity, Auto Mechanics, Metal Work, Further Mathematics, Food and Nutrition and Geography.
At least passes in Chemistry, Biology / Agricultural Science / Food and Nutrition.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Urban and Regional Planning (URP) department.
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Nigerian Tertiary Institutions Offering Orthopaedic and Plaster Technology Course