If you are planning to study Surveying and Geoinformatics at Plateau State Polytechnic, Barkin-Ladi located in Plateau State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into PLAPOLY.
Does Plateau State Polytechnic, Barkin-Ladi (PLAPOLY) offer Surveying and Geoinformatics?
No, Plateau State Polytechnic, Barkin-Ladi does not offer Surveying and Geoinformatics under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Plateau State Polytechnic, Barkin-Ladi (PLAPOLY) below to check if the Surveying and Geoinformatics course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Surveying and Geoinformatics When Accredited in Plateau State Polytechnic, Barkin-Ladi (PLAPOLY)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
JAMB Subject Combination
Chemistry, Geography, Art, Biology and Economics.
PLAPOLY Cut-Off Mark for Surveying and Geoinformatics
The general UTME cut-off mark is 180, but due to the variation of Surveying and Geoinformatics cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from PLAPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other PLAPOLY Science Courses with their Requirements
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates seeking admission into the Urban and Regional Planning (URP) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Building Technology (BT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Mechanical Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Mechanical Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Science Laboratory Technology (SLT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Electrical / Electronic Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science Subject.
Metallurgical Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Metallurgical Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work,
Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
Civil Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Civil Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any one other subject from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Nigerian Polytechnics Offering Surveying and Geoinformatics Course