If you are planning to study Automobile Technology Education at Redeemer's University, Nigeria located in Osun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. RUN was established in 2005 by the Redeemed Christian Church of God (RCCG) to provide university education rooted in academic excellence, innovation, and strong moral values. Since its inception, the university has developed into one of Nigeria’s leading private institutions of higher learning. This page explains everything you need to know to increase your chances of gaining admission into RUN.
Does Redeemer's University, Nigeria (RUN) offer Automobile Technology Education?
No, Redeemer's University, Nigeria does not offer Automobile Technology Education under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Redeemer's University, Nigeria (RUN) below to check if the Automobile Technology Education course under the Faculty of Education has been updated.
Admission Requirements for Automobile Technology Education When Accredited in Redeemer's University, Nigeria (RUN)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Automobile Technology Education department under Faculty of Education, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology /Agricultural Science, Physics, or Chemistry and
two (2) from General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
RUN Cut-Off Mark for Automobile Technology Education
The general UTME cut-off mark is 180, but due to the variation of Automobile Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from RUN Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other RUN Science Courses with their Requirements
1. Building Technology (BT)
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
2. Surveying and Geoinformatics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
3. Quantity Surveying (QS)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Quantity Surveying (QS) department.
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
4. Electrical / Electronics Engineering
To study this course, candidates aspiring to gain admission into Electrical / Electronics Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
5. Mechanical Engineering
To study this course, candidates seeking admission into the Mechanical Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant Science subjects.
6. Statistics
To study this course, candidates seeking admission into the Statistics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other relevant subject.
7. Meteorology
To study this course, candidates aspiring to gain admission into Meteorology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
either Chemistry or Geography.
Nigerian Tertiary Institutions Offering Automobile Technology Education Course