If you are planning to study Environmental Science and Technology at Redeemer's University, Nigeria located in Osun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. RUN was established in 2005 by the Redeemed Christian Church of God (RCCG) to provide university education rooted in academic excellence, innovation, and strong moral values. Since its inception, the university has developed into one of Nigeria’s leading private institutions of higher learning. This page explains everything you need to know to increase your chances of gaining admission into RUN.
Does Redeemer's University, Nigeria (RUN) offer Environmental Science and Technology?
No, Redeemer's University, Nigeria does not offer Environmental Science and Technology under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Redeemer's University, Nigeria (RUN) below to check if the Environmental Science and Technology course under the Faculty of Science has been updated.
Admission Requirements for Environmental Science and Technology When Accredited in Redeemer's University, Nigeria (RUN)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Environmental Science and Technology department under Faculty of Science, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
two (2) other Science subject.
RUN Cut-Off Mark for Environmental Science and Technology
The general UTME cut-off mark is 180, but due to the variation of Environmental Science and Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from RUN Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other RUN Science Courses with their Requirements
1. Industrial Chemistry
To study this course, candidates seeking admission into the Industrial Chemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science.
2. Urban and Regional Planning (URP)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Urban and Regional Planning (URP) department.
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
3. Quantity Surveying (QS)
To study this course, the minimum requirement for applicants seeking admission to the Quantity Surveying (QS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
4. Physics With Electronics
To study this course, candidates aspiring to gain admission into Physics With Electronics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject from Further Mathematics and Biology / Agricultural Science.
5. Electrical / Electronics Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Electrical / Electronics Engineering department.
any other Science subject.
6. Building Technology (BT)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
7. Applied Biology and Genetics
To study this course, candidates aspiring to gain admission into Applied Biology and Genetics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Nigerian Tertiary Institutions Offering Environmental Science and Technology Course