If you are planning to study Fisheries and Aquaculture Technology at Redeemer's University, Nigeria located in Osun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. RUN was established in 2005 by the Redeemed Christian Church of God (RCCG) to provide university education rooted in academic excellence, innovation, and strong moral values. Since its inception, the university has developed into one of Nigeria’s leading private institutions of higher learning. This page explains everything you need to know to increase your chances of gaining admission into RUN.
Does Redeemer's University, Nigeria (RUN) offer Fisheries and Aquaculture Technology?
No, Redeemer's University, Nigeria does not offer Fisheries and Aquaculture Technology under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Redeemer's University, Nigeria (RUN) below to check if the Fisheries and Aquaculture Technology course under the Faculty of Agriculture has been updated.
Admission Requirements for Fisheries and Aquaculture Technology When Accredited in Redeemer's University, Nigeria (RUN)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Fisheries and Aquaculture Technology department under Faculty of Agriculture, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science,
Physics / Geography / Economics.
JAMB Subject Combination
Biology / Agricultural Science.
RUN Cut-Off Mark for Fisheries and Aquaculture Technology
The general UTME cut-off mark is 180, but due to the variation of Fisheries and Aquaculture Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from RUN Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other RUN Science Courses with their Requirements
1. Architecture
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
2. Civil Engineering
To study this course, the minimum requirement for applicants seeking admission to the Civil Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
3. Microbiology
To study this course, the minimum requirement for applicants seeking admission to the Microbiology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
4. Industrial Chemistry
To study this course, the minimum requirement for applicants seeking admission to the Industrial Chemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science.
5. Geology
To study this course, the minimum requirement for applicants seeking admission to the Geology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other relevant subject.
6. Applied Geophysics
To study this course, candidates aspiring to gain admission into Applied Geophysics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
7. Building Technology (BT)
To study this course, candidates seeking admission into the Building Technology (BT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Nigerian Tertiary Institutions Offering Fisheries and Aquaculture Technology Course