If you are planning to study Industrial Chemistry and Chemical Entrepreneurship at Redeemer's University, Nigeria located in Osun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into RUN.
Does Redeemer's University, Nigeria (RUN) offer Industrial Chemistry and Chemical Entrepreneurship?
No, Redeemer's University, Nigeria does not offer Industrial Chemistry and Chemical Entrepreneurship under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Redeemer's University, Nigeria (RUN) below to check if the Industrial Chemistry and Chemical Entrepreneurship course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Industrial Chemistry and Chemical Entrepreneurship When Accredited in Redeemer's University, Nigeria (RUN)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Industrial Chemistry and Chemical Entrepreneurship department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) science subjects.
JAMB Subject Combination
any two (2) science subjects.
RUN Cut-Off Mark for Industrial Chemistry and Chemical Entrepreneurship
The general UTME cut-off mark is 180, but due to the variation of Industrial Chemistry and Chemical Entrepreneurship cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from RUN Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other RUN Science Courses with their Requirements
Human Anatomy
SSCE Requirements
To study this course, candidates aspiring to gain admission into Human Anatomy department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Applied Biology and Genetics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Applied Biology and Genetics department.
Building Technology (BT)
SSCE Requirements
To study this course, candidates seeking admission into the Building Technology (BT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Physics With Electronics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Physics With Electronics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject from Further Mathematics and Biology / Agricultural Science.
Surveying and Geoinformatics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Architecture
SSCE Requirements
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Mechanical Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Engineering department.
any two (2) other relevant Science subjects.
Nigerian Tertiary Institutions Offering Industrial Chemistry and Chemical Entrepreneurship Course