If you are planning to study Optometry at Redeemer's University, Nigeria located in Osun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. RUN was established in 2005 by the Redeemed Christian Church of God (RCCG) to provide university education rooted in academic excellence, innovation, and strong moral values. Since its inception, the university has developed into one of Nigeria’s leading private institutions of higher learning. This page explains everything you need to know to increase your chances of gaining admission into RUN.
Does Redeemer's University, Nigeria (RUN) offer Optometry?
No, Redeemer's University, Nigeria does not offer Optometry under its Faculty of Health and Medical Sciences. However, since our course list is updated regularly, you can visit the courses available at Redeemer's University, Nigeria (RUN) below to check if the Optometry course under the Faculty of Health and Medical Sciences has been updated.
Admission Requirements for Optometry When Accredited in Redeemer's University, Nigeria (RUN)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Optometry department under Faculty of Health and Medical Sciences, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Physics, Chemistry, Biology and
Additional / Further Mathematics.
RUN Cut-Off Mark for Optometry
The general UTME cut-off mark is 230, but due to the variation of Optometry cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from RUN Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other RUN Science Courses with their Requirements
1. Surveying and Geoinformatics
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
2. Building Technology (BT)
To study this course, candidates seeking admission into the Building Technology (BT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
3. Physiotherapy
To study this course, candidates seeking admission into the Physiotherapy department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
4. Geology
To study this course, candidates aspiring to gain admission into Geology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other relevant subject.
5. Human Physiology
To study this course, the minimum requirement for applicants seeking admission to the Human Physiology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
6. Architecture
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
7. Urban and Regional Planning (URP)
To study this course, the minimum requirement for applicants seeking admission to the Urban and Regional Planning (URP) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Nigerian Universities Offering Optometry Course